Skip to the guide

Power connections

Busbar Insulation Paint or Epoxy Powder

Use Glyptal 8001 red enamel at 1800 V/mil average when the coat is paint on a bus bar. Use Storm epoxy powder after fabrication at a typical 800 volts per mil and 6 to 120 mils.

Rust Belt Industrials · November 11, 2026 · 6 min read

On this page

Use Glyptal 8001 when the coat is a red insulating enamel on a bus bar, applied by spray, dip, or flow coat, and air-dried or baked. As of November 11, 2026, Glyptal's product data sheet 8001 lists dielectric strength of 1800 V/mil average to ASTM D115-55, and it names bus bars among the suggested uses. Use Storm epoxy powder when the insulation goes on after bending, contouring, punching, and milling. Storm's June 2023 applications note, opened the same day, prints a typical thickness of 6 to 120 mils and a typical insulation rating of 800 volts per mil. Heat-shrink tubing, as an alternative to either coat, is the epoxy and BBIT page. A tape wrap is the tape page.

Enamel is a wet film. Powder is applied after the bar is formed

Glyptal 8001 is an iron oxide red enamel. The sheet says films can be air-dried or baked, and that the paint is suggested for motor stators, field coils, end windings, bus bars, and switch bases. It also says the paint can be a metal primer where some corrosion resistance is needed, and that it is not suitable for the inside coating of dielectric oil containers. Storm's note describes epoxy powder as a coating fused in an oven after the bar is already bent and punched, so the film is not asked to stretch around a later bend. The note says powder is a conformal coating and distinguishes it from a wet paint film. The choice on this page follows that split: 8001 when the bus bar takes the enamel sheet, and the powder note when the coat is applied after fabrication.

Coat lines opened November 11, 2026. Glyptal 8001 is the enamel sheet. Storm's figures are the June 2023 powder note.
CoatDielectric lineThicknessHeat
Glyptal 80011800 V/mil average, ASTM D115-55Coverage is printed at 1 mil dry film, 650 ft²/galAir dry hard overnight. Bake 225°F to 275°F for 1 to 3 hours.
Storm epoxy powderTypical insulation rating 800 volts per mil. Dielectric strength depends on process, thickness, and preparation.Typical range 6 to 120 mils. Fluidized bed for 5 kV up to 35 kV at 50 to 120 mils.Typical 130°C, characterized by UL 94 V-0, depending on the formulation.

Glyptal 8001 prints 1800 V/mil as an average

The 8001 sheet opened November 11, 2026 lists a wet sample at 56 to 59 percent solids by weight, viscosity 80 to 85 KU, flashpoint below 80°F on a closed cup, and solid weight 13.76 plus or minus 0.2 lb/gal. Dielectric strength is 1800 V/mil average to ASTM D115-55. Arc resistance on Textolite is 30 seconds. Dry to touch is 4 to 6 hours. Air dry hard is overnight. Recoat is overnight. The bake schedule is 225°F to 275°F for 1 to 3 hours. Coverage at 1 mil dry-film thickness is 650 ft²/gal. Application is spray, dip, or flow coat, on a clean dry surface, at temperatures above 50°F. Spray reduction uses 1500 thinner to 24 to 28 seconds on a number 2 Zahn cup. Dip or flow reduction uses Aromatic 100 to 30 to 35 seconds on the same cup. The sheet says Glyptal does not control the use, and that each user tests the material for the particular job. The 1800 V/mil figure stays an average from ASTM D115-55 on that sheet.

Powder thickness is 6 to 120 mils, at a typical 800 volts per mil

Storm's June 2023 note says the typical powder thickness is 6 to 120 mils, which it also writes as 0.006 to 0.120 inch, and that the powder is applied after bending, contouring, punching, and milling. The electrical line is a typical insulation rating of 800 volts per mil, with dielectric strength depending on the application process, the coating thickness, and bus bar preparation. Temperature is a typical value of 130°C, characterized by UL 94 V-0, depending on the formulation and the application. The note says fairly flat bars suit electrostatic spray, and bars with many turns and tight bends suit a fluidized bed. The fluidized-bed sentence names higher voltages such as 5 kV and up to 35 kV, at coating thicknesses of 50 to 120 mils. Fairly flat bars are the spray geometry on that note.

The same note's design list for a powder-coated bar, opened November 11, 2026, says to round edges and corners, at least 1 mm for thin bars, so the coat does not thin out on the edge. It asks for two drawings: the copper or aluminum substrate, and the coated thickness. Holes are countersunk and deburred. Hole diameter is at least 1.5 times to 2 times the bus bar thickness, because a smaller hole can fill with powder and crack after cure. Hardware through a coated hole can crack the coat if the torque is excessive, unless that area is masked. The note names a high-potential test as a pass or fail check that no current flows, an ultrasound check of thickness, and, for a laminated bar, partial discharge and insulation resistance. It does not print a hipot voltage.

What to copy onto the coat line

  • Coat: Glyptal 8001, or Storm epoxy powder from the June 2023 note, as opened November 11, 2026.
  • 8001: red enamel, 1800 V/mil average to ASTM D115-55, bus bars listed as a suggested use.
  • 8001 film: above 50°F, air dry or bake at 225°F to 275°F for 1 to 3 hours. The sheet says it is not for the inside of a dielectric oil container.
  • Powder: after bend, punch, and mill. Typical 6 to 120 mils. Typical 800 volts per mil. Typical 130°C.
  • Powder method: spray for a fairly flat bar. Fluidized bed for many turns, and for the note's 5 kV to 35 kV line at 50 to 120 mils.
  • Powder holes: diameter at least 1.5 times to 2 times the bar thickness. Edge radius at least 1 mm on a thin bar. Two drawings, substrate and coated thickness.
  • Bend radius for the bar, before powder, is the copper and aluminum radius page.

Busbar enamel or powder note

Name Glyptal 8001 or epoxy powder. Copy the dielectric line and the thickness from that sheet.

This prepares a request. It does not send one.

Questions the enamel sheet and the powder note answer

Which volts-per-mil figure is the enamel?

Glyptal 8001 prints 1800 V/mil average to ASTM D115-55, as of November 11, 2026. Storm's powder note prints a typical 800 volts per mil. The two figures stay on their own sheets.

What hole diameter does the powder note ask for?

At least 1.5 times to 2 times the bus bar thickness, as of November 11, 2026. The note says a smaller hole can fill with powder and crack after cure.

Can 8001 coat the inside of an oil-filled container?

The 8001 sheet says the paint is not suitable for the inside coating of dielectric oil containers, as of November 11, 2026. Bus bars, switch bases, and the motor parts named on the sheet are the suggested uses.

Sources

The 1800 V/mil average, the bus bar use line, the bake schedule, and the oil-container line are from Glyptal product data sheet 8001. The 6 to 120 mil range, the 800 volts per mil rating, the 130°C line, the 5 kV to 35 kV fluidized-bed sentence, and the hole-diameter rule are from Storm's June 2023 epoxy applications note. Both were opened November 11, 2026.